/https://hosting-media.riverside.com/media/imports/podcasts/e35cbd1e-807e-42bd-bae5-29e4d466fa36/1949ec0a-5a6b-416a-acf0-ac87f4eeb487.jpg)
Manufacturing Culture Podcast
Jim Mayer
Paul Van Metre | Where Did the Culture Go?
NOV 17, 202622 MIN
/https://hosting-media.riverside.com/media/imports/podcasts/e35cbd1e-807e-42bd-bae5-29e4d466fa36/1949ec0a-5a6b-416a-acf0-ac87f4eeb487.jpg)
Description
In 1997, Paul Van Metre and a few friends opened a machine shop near Seattle straight out of college, with one machine and money from a second mortgage. Over 17 years that shop, ProCNC, grew to about 75 people, came back from the edge of bankruptcy after 9/11, and built its own software to run the floor. That software became ProShop ERP. Paul was one of the very first guests on the Manufacturing Culture Podcast, and three years later he's back with his first book, Precision Manufacturing, Precision Business: How the Best Machine Shops Turn Discipline into Profit.
What sets Paul apart from other leaders is how plainly he owns his own mistakes. He was the machinist who could hold a part to a tenth and the owner who rode feast and famine cycles because no one was selling while everyone was making parts. He's the boss who once assumed people weren't trying hard enough, then learned he hadn't set them up to succeed. He built the book out of those lessons and the voices of about fifty shop owners and leaders he's interviewed on Machine Shop Mastery.
Jim finally asks the question he's held for three years: where did the culture go? Paul answers that culture is the pillar everything else stands on. They talk about the one person deep problem and what it feels like to run a shop that depends on one person, why scrap almost always starts upstream, tough love as the space between family and team, the pride of putting fifty humble people in a book, and what makes Paul proud: hearing that his work changed someone's life.
Key Takeaways
Culture is the foundation, not a chapter. Paul's book puts people, culture and standards in section four of five, and he says maybe it should have been part one. Without a good culture, people won't adopt systems, won't adhere to them and won't help make them better.
Most shops run one person deep. The setup machinist, the estimator, the office manager, the person in shipping and receiving. If one of them took two weeks of vacation, Paul says, that part of the business would grind to a halt, and the fixes are not that hard and cost hardly any money.
Retirements make it urgent. So many people in manufacturing are baby boomers who are retiring or about to. In Paul's words, the industry is "right in the meaty part of that retirement curve."
Scrap usually starts upstream. On rare occasions a person causes the mistake, Paul says, but more often it's something they didn't have, a process that wasn't in place, or ambiguity. The owner's job is to make sure everyone downstream of a new order knows what good looks like.
Hold a high bar and say you care. For the space between a family (love without accountability) and a team (accountability without always love), Paul's answer is tough love: "you can express deep caring for them and also expect a lot out of them."
Chapters
00:00 Welcome back: three years since Paul's first episode
02:35 Icebreaker: Paul's life as a movie
04:03 What culture means to Paul
05:34 Why Paul wrote the book
07:01 Where did the culture go?
09:11 The one person deep problem
10:49 Retirements and the one person problem
11:30 Scrap is a process problem, not the machinist's fault
13:18 Running a business with a machinist's precision
15:27 Jim's own one person problem
16:47 When to hand off a hat
17:40 Love, accountability and tough love
20:08 Paul's favorite part of writing the book
21:38 What to act on Monday morning
23:04 What makes Paul proud
23:55 Signed copies, team orders and free copies
24:47 Closing thoughts
Find Paul
LinkedIn: Paul Van Metre
Book: disciplinetoprofit.com
Podcasts: host of Machine Shop Mastery
Company: proshoperp.com

